Serving the Tacoma area  ·  (253) 276-7144  ·  Open Mon-Sun 7am-7pm
📞 (253) 276-7144 Free Quote

Metal Roofing in Fife, WA (98424) · Local Professionals

Tacoma Metal Roofing · Fast response in Fife and the Tacoma area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+251Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Fife is a working town, and its roofs show it. Between the warehouse rows along Pacific Highway East and the older single-story homes tucked off 54th Avenue, most properties here sit on flat valley ground that holds moisture long after the rain stops. That combination of long wet winters, dense tree cover, and low-slope roofs is exactly what wears roofing down in 98424.

We are Tacoma Metal Roofing, and we work Fife every week. Whether you are managing a shop near the Fife Curve, own a rental off Valley Avenue East, or live in one of the older houses near Discovery Pond, we can get out, look at the roof, and tell you straight what it needs.

Metal Roofing in Fife (98424)

Fife sits on the valley floor, and that shapes almost every roofing job here. The ground stays wet through the winter, so we pay close attention to how water leaves the roof and where it goes once it hits the ground. On the commercial side, the warehouses and light industrial buildings along Pacific Highway East and 70th Avenue East usually have low-slope roofs where ponding and fastener back-out are the main problems. On the residential side, the older homes off 54th and Valley Avenue often have mature Douglas fir and cedar overhead, which means needles in the gutters, moss on the north slopes, and limbs that come down in a south wind. We plan for all of it, from panel choice to gutter sizing.

Our team has worked Fife and the surrounding Pierce County area long enough to know which streets have tight access for a lift, which properties back up to the Port of Tacoma rail lines, and where a metal roof over existing shingles makes sense versus a full tear-off. We install standing seam, corrugated and ribbed panels, metal shingle, and stone-coated steel, and we repair the flashing and fasteners that fail most often in this climate.

Our services in Fife

How a Job Works in Fife

It starts with a call to (253) 276-7144 or a request through our site. We schedule a free on-site assessment, and that means a real look at the roof, the attic if we can get in, the gutters, and the flashing around chimneys and skylights. We take photos, measure the roof, and talk through what we see. You get a written estimate with the panel type, the price per square foot, and the line items spelled out.

Once you approve, we pull the permit with the City of Fife (rules vary by jurisdiction, so we verify the current requirements before we file) and schedule the work. On tighter lots off 54th Avenue, we stage materials in the driveway or on the street with a traffic plan, and we keep the crew moving so your business or household is not disrupted longer than necessary. For commercial buildings near the Fife Curve, we often work in sections so the shop stays open.

When the job is done, we walk the property with you, magnet-sweep the lawn and driveway for nails, and haul away every scrap of old roofing and packaging. We leave your property clean, and we do not consider the job finished until you have looked it over with us.

Pricing in Fife depends on the roof, not just the square footage. As a ballpark, corrugated and ribbed panel roofing starts around $5.50 per square foot, metal roof installation around $8, standing seam around $10, and metal roof replacement around $9. A retrofit over existing shingles starts around $7 per square foot, but code limits how many layers can stay, so we confirm that first. Repairs and leak calls start around $450, screw replacement and re-fastening around $750, and flashing, chimney, or skylight repair around $600. Coating and painting starts around $2.50 per square foot, and gutters for metal roofs run about $9 per linear foot.

The biggest cost factors are roof size and pitch, access (a tight lot off Valley Avenue East takes more labor than an open warehouse roof), the condition of the decking and flashing, and urgency. Storm and wind damage calls get a free inspection, and we document what we find for your insurance company. Call (253) 276-7144 for a free estimate.

My older house off 54th Avenue has big cedar and fir trees overhead. Does that change what metal roof you recommend?
Yes. Heavy needle drop and shade mean moss and debris sit on the roof longer, so we usually recommend a standing seam or a ribbed panel with a smooth finish that sheds needles, plus oversized gutters and a good cleaning plan. On shady north slopes we also talk about a coating that resists algae. We look at the tree cover during the free assessment and price accordingly.
A windstorm just peeled back panels on my shop near the Fife Curve. How fast can you get out?
We prioritize active leaks and wind damage in Fife and the surrounding area. Call (253) 276-7144, and we will schedule a free inspection as quickly as we can, usually within a day or two depending on storm volume. We can tarp or secure the roof to stop water intrusion while you wait for the repair or insurance process.
What does a typical metal roof replacement cost for a house in 98424?
Most Fife homes fall in the $9 to $14 per square foot range for replacement, depending on panel type, roof complexity, and whether we tear off the old roof or retrofit. A simple ranch is toward the lower end; a cut-up roof with dormers and valleys is higher. We give you a written number after the free on-site measure.
Do I need a permit from the City of Fife for a metal roof?
In most cases yes, a roofing permit is required for a full replacement or re-roof, and the thresholds and inspection requirements are set by the City of Fife. We verify the current rules with the city before we file and handle the permit as part of the job. Historic district or HOA design review can also apply, so we check that early.
My neighbor and I disagree about where the property line is, and my new roof overhang may cross it. What do we do?
Property line disputes are a civil matter, so we recommend confirming the line with a survey before work starts. We can adjust the panel layout or overhang to stay within your side once the line is clear. If your property is in an HOA, we also help coordinate the design approval so the panel profile and color meet the association rules.
Is your crew covered by insurance if someone gets hurt on my Fife property?
Yes. We are fully insured with general liability and workers' compensation coverage.
What maintenance should I do on a metal roof in Fife between rainy seasons?
Late summer is the best time. Clear needles and debris from the gutters and valleys, check the fasteners and seals around flashing, and look for moss or algae on north slopes. A quick inspection now prevents the leaks that show up in November. We offer free estimates for inspections and can set up a maintenance plan.
Why choose us?

Trusted professionals in Tacoma

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Tacoma

All your work handled by qualified professionals in Tacoma

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

251+ Verified Client Reviews in Tacoma

⭐⭐⭐⭐⭐ 4.9/5 · 251 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Tacoma · Response within 24h · No commitment · ☎ (253) 276-7144

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Tacoma ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm